Westinghouse iGen160s
155 Wh, 100 W
Bluetti Elite 10
Power station · Elite. Specs from the manufacturer page (checked ).
The Bluetti Elite 10 is a 128 Wh portable power station with 200 W output. It uses LiFePO4 battery chemistry.
Check on Amazon →Sponsored link; we may earn a commission.
Capacity
128Wh
Continuous
200W
Chemistry
LiFePO4
Key features
- 128 Wh capacity
- 200 W output
- LiFePO4 battery chemistry
Specifications
| Capacity | 128 Wh |
|---|---|
| Continuous output | 200 W |
| Battery chemistry | LiFePO4 |
From the Bluetti page. Values the manufacturer does not publish are left out.
How long it runs common appliances
| Appliance | Watts | Runs? | Hours |
|---|---|---|---|
| Refrigerator (with freezer) | 120 W (600 start) | surge too high | — |
| Chest freezer | 100 W (500 start) | surge too high | — |
| CPAP (no humidifier) | 35 W (40 start) | yes | 2.9 h |
| Gas boiler (pump + controls) | 120 W (300 start) | surge too high | — |
| Wi-Fi router + modem/ONU | 12 W | yes | 8.4 h |
| Starlink (standard dish) | 60 W (100 start) | yes | 1.7 h |
| TV 50" | 75 W | yes | 1.4 h |
| Sump pump 1/2 HP | 920 W (2150 start) | surge too high | — |
| Well pump 1/2 HP | 880 W (2000 start) | surge too high | — |
| Space heater 1500 W | 1500 W | surge too high | — |
Assumes 88 % inverter efficiency, 90 % usable capacity and typical duty cycles. Build your own list in the calculator.
Similar portable power stations
Marbero M270
150 Wh, 100 W
Connection and wiring
Follow the diagrams in the Bluetti manual.
Open the Bluetti manual (PDF) →
Error codes and troubleshooting
| Code | Meaning | What to do | Manual page |
|---|---|---|---|
| E004 | The output voltage is outside the expected range, or the grid connection is not proper. | Ensure the output voltage is within ±10% of the rated voltage or proper grid connection. | 21 |
| E016 | The internal fan is blocked, unplugged, or not functioning properly. | Check if the fan is blocked, unplugged, or not functioning properly. Ensure proper ventilation. | 21 |
| E117 | Grid oscillation has been detected at the grid input. | Disconnect the grid input and contact BLUETTI support for further assistance. Call service if it persists. | 21 |
| E074 | The battery management system (BMS) has detected a fault. The specific fault is shown in the mobile app. | Check the specific fault in the mobile app. If the battery is too hot or too cold, let the unit reach a suitable temperature before charging or using it (charging -15°C to 40°C; discharging -25°C to 40°C). | 22 |
| Others | Other errors not listed in the error code table. | Contact BLUETTI support for help. Call service if it persists. | 22 |
| E001 | The inverter is overloaded because the connected devices draw too much power. | Check whether the power consumption of your devices is too high. Reduce the load if necessary. | 23 |
6 of 23 codes. From the Bluetti manual. All 23 Elite 200 V2 / Apex 300 / Elite 100 V2 / AC70 codes →
FAQ
How long will the Bluetti Elite 10 run a refrigerator?
About 2 hours for a typical 120 W refrigerator that runs 35 % of the time, after inverter and depth-of-discharge losses.
Can the Bluetti Elite 10 start a sump pump or well pump?
Starting surge matters more than running watts: this unit is rated 200 W output (no separate peak published). That is below a typical 1/2 HP sump pump start (about 2150 W); check your pump label. Use the calculator with your exact pump.