DuroMax XP16000iH
13000 W, dual-fuel
Pulsar PGD170TiSRCO
Generator. Specs from the manufacturer page (checked ).
The Pulsar PGD170TiSRCO is a tri-fuel inverter generator that runs on gasoline, propane, or natural gas, rated at 14,500 running watts and 17,000 peak watts on gasoline. It has a built-in ATS inlet for automatic backup power integration, a 760cc V-twin engine, and a 10.6-gallon fuel tank.
Check on Amazon →Sponsored link; we may earn a commission.
Running
14500W
Peak / surge
17000W
Fuel
tri-fuel
Key features
- Runs on gasoline, propane, or natural gas
- 14,500 running watts and 17,000 peak watts on gasoline
- Three starting options: recoil, one-push electric, and remote start
- 760cc 2V82F V-twin engine with up to 10 hours of runtime at half load
- Built-in ATS inlet for automatic backup power applications
- Outlets: 120V/240V 14-50R and L14-30R, one 120V L5-30R, four 120V 5-20R GFCI, USB-A, USB-C, and 12V DC
- Economy switch adjusts engine speed based on demand
- CO Sentry carbon monoxide detection and LCD display
What it is for
- home backup
- jobsite
- emergency use
Specifications
| Running watts | 14500 W |
|---|---|
| Peak / surge | 17000 W |
| Fuel | tri-fuel |
| AC output voltage | 120V/240V |
From the Pulsar page. Values the manufacturer does not publish are left out.
Similar inverter & portable generators
DuroMax XP16000iHT
13000 W, tri-fuel
DuroMax XP15000EH
12500 W, dual-fuel
DuroMax XP15000HX
12000 W, dual-fuel
DuroMax XP15000HXT
12000 W, tri-fuel
Generac GP18000EFI
18000 W
DuroMax XP13000EH
10500 W, dual-fuel
DuroMax XP13000HX
10500 W, dual-fuel
On our lists
Connection and wiring
Follow the diagrams in the Pulsar manual. Connecting to a home panel needs a transfer switch or interlock and a licensed electrician.
- Electrical schematic, manual page 2 →
- Parallel connection, manual page 15 →
- Electrical schematic, manual page 26 →
Error codes and troubleshooting
| Code | Meaning | What to do | Manual page |
|---|---|---|---|
| RED | Carbon monoxide has accumulated around the generator and the unit shut off due to a CO hazard. The red light flashes for at least five minutes after shut-off. Automatic shutoff with a flashing red light means the generator was improperly located. | Move the generator to an open outdoor area far from occupied spaces, with the exhaust pointed away. Once it is in a safe area, it can be restarted. Introduce fresh air and ventilate the area where the generator shut down. | 4 |
| YELLOW | A CO Sentry system fault occurred. The generator shut down automatically, and the yellow light flashes for at least five minutes after the fault. | The generator can be restarted, but it may continue to shut off. | 4 |
| CO | Detects the presence of carbon monoxide and may shut down the unit automatically for safety. | The manual gives no specific reset step for this indicator. If dizziness, weakness, or nausea occur, turn the unit off, move to fresh air, and seek medical attention. Operate only outdoors, away from enclosed spaces. | 5 |
| Low Oil LED | The engine oil level has fallen below the safe operating limit (270 ml or less). The engine shuts off automatically and cannot restart until the proper oil amount is added. | Add the appropriate oil until the level is at the proper mark. SAE 10W-30 is recommended for general use. Do not run the engine with too little oil. | 14 |
| OVERLOAD | The total load on the outlets exceeds the generator's running power. If the light turns on and the generator stops producing power, it has been overloaded. The light may flash briefly when a large device starts. | Turn off and disconnect all electrical devices and stop the engine. Compare device requirements to the generator rating and reduce connected wattage if necessary. Check and reset any tripped circuit breakers, then restart and reconnect devices without overloading. | 14 |
| LOW OIL | The engine oil level is too low. The engine shuts off automatically when the oil falls below a critical level. | Add the appropriate oil, SAE 10w-30 recommended for general use, until the oil is at the proper level. The engine cannot be restarted until the proper amount of oil has been added. | 15 |
6 of 8 codes. From the Pulsar manual. All 8 PG12000BCO / PG7750BCO / PG6580BCO / PG105TiSRCO codes →
FAQ
Can the Pulsar PGD170TiSRCO start a sump pump or well pump?
Starting surge matters more than running watts: this unit is rated 17000 W peak. That covers a typical 1/2 HP sump pump (about 2150 W to start). Use the calculator with your exact pump.