A-iPower SUA1500i
1200 W, gasoline
Pulsar PG1500iS
Generator · Pulsar. Specs from the manufacturer page (checked ).
The Pulsar PG1500iS is a gasoline-powered inverter generator rated at 1,200 running watts and 1,500 peak watts. It uses a 56cc OHV 4-stroke engine with a recoil start and runs at 57 dB. It has two 120V AC outlets, USB-A, USB-C, and 12V DC ports.
View at Pulsar →Sponsored link; we may earn a commission.
Running
1200W
Peak / surge
1500W
Fuel
gasoline
Run time @50 %
5h
Noise
57dB
Weight
12.25kg
Key features
- 1,200 running watts and 1,500 peak watts
- 56cc OHV 4-stroke gasoline engine with recoil start
- Runs at 57 dB
- Runs up to 5 hours at half load with low idle control
- Parallel ready: a second unit doubles power
- Outlets: (2) 120V AC, (1) USB-A, (1) USB-C, (1) 12V DC
- Overload protection, short circuit protection, and low oil shut-off
- Weighs 27 lbs
What it is for
- emergency power
- outdoor recreation
- RV parks
- campsites
Specifications
| Running watts | 1200 W |
|---|---|
| Peak / surge | 1500 W |
| Fuel | gasoline |
| Run time at 50 % load | 5 h |
| Noise | 57 dB |
| AC output voltage | 120V |
| Weight | 12.25 kg (27.0 lb) |
From the Pulsar page. Values the manufacturer does not publish are left out.
Similar inverter & portable generators
A-iPower GXS1700i
1300 W, gasoline
A-iPower SC2000i
1600 W, gasoline
A-iPower SUA2000iD
1600 W, dual-fuel
GenMax GM2000i
1600 W, gasoline
Champion 2000-Watt Ultralight Inverter
1700 W, gasoline
Firman W01781
1700 W, gasoline
Firman W01785
1700 W
Connection and wiring
Follow the diagrams in the Pulsar manual. Connecting to a home panel needs a transfer switch or interlock and a licensed electrician.
Open the Pulsar manual (PDF) →
Error codes and troubleshooting
| Code | Meaning | What to do | Manual page |
|---|---|---|---|
| Engine Overload Indicator Light | The connected devices have exceeded the generator's wattage or amperage capacity, or a power surge occurred. The green AC Pilot light goes off, and power to connected devices stops while the engine keeps running. | Disconnect all electronic devices and stop the engine. Reduce the total connected wattage to within the rated output. Inspect the air inlet and control panel for blockage and clear any found, then restart the engine. | 8 |
| OUTPUT OVERLOAD | The inverter has been overloaded beyond its wattage or amperage capacity, or by a power surge. The green AC pilot light goes off, the engine keeps running, and power to the connected loads stops. The light may flash briefly on starting a load due to surge and is normal. | Reduce the load and press the RESET button. If resetting does not solve the problem, disconnect the load and shut down the engine. Inspect the air inlet and air outlet for blockage and remove any found. | 8 |
| Oil Warning Indicator Light | Oil has fallen below the minimum level. The light comes on and the engine stops automatically. | Add the correct volume of engine oil (SAE 10W-30) to the crankcase. The engine will not start until the correct oil volume is in the crankcase. | 8 |
| DC Circuit Breaker | The DC circuit breaker turns OFF automatically when connected loads exceed the generator's rated output, and the generator stops supplying power. | Reduce the connected loads to within rated DC output, then return the DC Circuit Breaker to the ON position to restore power. If the breaker turns off again, stop using the generator immediately and consult a local, authorized Pulsar dealer. Call service if it persists. | 9 |
From the Pulsar manual. All 4 2200W Dual Fuel Inverter / PG1500iS / G2319N codes →
FAQ
How long does the Pulsar PG1500iS run on a tank?
The maker rates it at 5 hours at 50 % load (about 600 W). A light load such as a refrigerator and lights runs longer; a full load runs shorter.
Can the Pulsar PG1500iS start a sump pump or well pump?
Starting surge matters more than running watts: this unit is rated 1500 W peak. That is below a typical 1/2 HP sump pump start (about 2150 W); check your pump label. Use the calculator with your exact pump.