Bluetti Elite 100 mini
1004.8 Wh, 700 W
Klein Tools KTB1000
Power station. Specs from the manufacturer page (checked ).
The Klein Tools KTB1000 is a 983 Wh portable power station with 1500 W output. It uses a lithium-ion battery to power tools and electronics on the job site, with pure sine-wave power and no gas engine.
View at Klein Tools →Sponsored link; we may earn a commission.
Capacity
983Wh
Continuous
1500W
Key features
- 4 x AC outlets (120V / 1500W)
- Pure sine-wave power output
- 3 x 60W USB-C PD ports (5V-20V/3A) and 3 x USB-A ports (5V / 2.4A)
- 12V car port (12V/10A)
- Fast charge in 2.5 hrs from 0-80% with supplied chargers
- Solar compatible with built-in MPPT; 7.5 hours to charge from 0-80% with 2 60W Klein Tools solar panels (proper sunlight needed)
- Pass-through charging: power devices while the station charges
- Safe for indoor use, with a reusable, washable dust filter
What it is for
- job site
Specifications
| Capacity | 983 Wh |
|---|---|
| Continuous output | 1500 W |
| AC output voltage | 120V |
| Dimensions | 40.1 × 27.4 × 26.4 cm (15.8 × 10.8 × 10.4 in) |
From the Klein Tools page. Values the manufacturer does not publish are left out.
What is in the box
- Fast charger
- Mobile charger
- 12V car port adapter
How long it runs common appliances
| Appliance | Watts | Runs? | Hours |
|---|---|---|---|
| Refrigerator (with freezer) | 120 W (600 start) | yes | 19 h |
| Chest freezer | 100 W (500 start) | yes | 26 h |
| CPAP (no humidifier) | 35 W (40 start) | yes | 22 h |
| Gas boiler (pump + controls) | 120 W (300 start) | yes | 13 h |
| Wi-Fi router + modem/ONU | 12 W | yes | 65 h |
| Starlink (standard dish) | 60 W (100 start) | yes | 13 h |
| TV 50" | 75 W | yes | 10 h |
| Sump pump 1/2 HP | 920 W (2150 start) | surge too high | — |
| Well pump 1/2 HP | 880 W (2000 start) | surge too high | — |
| Space heater 1500 W | 1500 W | yes | 0.7 h |
Assumes 88 % inverter efficiency, 90 % usable capacity and typical duty cycles. Build your own list in the calculator.
Similar portable power stations
Pecron F1000LFP
960 Wh, 1500 W
Dabbsson 1000L
1008 Wh, 1200 W
DJI Power 1000 Mini
1008 Wh, 1000 W
Westinghouse iGen1000s
1008 Wh, 1500 W
Allpowers P1800
1024 Wh, 1800 W
Anker SOLIX C1000 Gen 2
1024 Wh, 2000 W
Bluetti AC2P
1024 Wh, 1800 W
Connection and wiring
Follow the diagrams in the Klein Tools manual.
Open the Klein Tools manual (PDF) →
Error codes and troubleshooting
| Code | Meaning | What to do | Manual page |
|---|---|---|---|
| Battery Malfunction | Flashing means the unit can no longer charge beyond 40% of its original capacity. If the icon stays lit without flashing, the unit has had an unrecoverable failure. | — | 3 |
| COLD | The unit's temperature is below the permissible operating range. The unit is not operational until it returns to the lowest acceptable operating temperature. | Allow the unit to warm to within the permissible operating temperature range before use. | 3 |
| HOT | The unit's temperature is above its rating, which can result from high loads in a high ambient environment. The unit is not operational until it cools to the permissible operating temperature range. | Stop the load and allow the unit to cool to the permissible operating temperature range before resuming use. | 3 |
| LOW | The input voltage is below the rating. The unit accepts only inputs that meet each port's specifications. When this icon is lit, the input is not charging the unit. | Confirm the input source supplies a 13V to 30V DC signal as listed in General Specifications. If the voltage is outside this range, the input port shuts off. | 3 |
| OL | Shown on the LCD when the power station is overloaded. The green indicators on overloaded ports flash for 10 seconds, and the ports shut down. An overloaded input port shuts off automatically. | Turn off all ports and disconnect all devices, including the charging cord. Check each device's power requirements against the unit's capacity. Reconnect only necessary devices, then turn on the USB, 12V, and/or AC outlets. If the unit will not reset, disconnect everything, wait 2 minutes, then activate the required ports and reconnect devices. | 5 |
| OL | The overload symbol "OL" appears on the display when a port is drawing more power than allowed. The green LED of the overloaded port flashes for 10 seconds to signal the overload. | Turn off all ports. Unplug all devices, including the battery's charging cable. Confirm that each device's maximum power requirement is within the battery's capacity. Reconnect only the necessary devices. Re-enable the USB, 12 V and/or AC outlets to resume charging. If an input port overloads, it shuts off automatically and reactivates once the input source meets the stated requirements. Recharge only with the supplied AC wall charger or the APP port. | 11 |
6 of 9 codes. From the Klein Tools manual. All 9 KTB1000 codes →
FAQ
How long will the Klein Tools KTB1000 run a refrigerator?
About 19 hours for a typical 120 W refrigerator that runs 35 % of the time, after inverter and depth-of-discharge losses.
Can the Klein Tools KTB1000 start a sump pump or well pump?
Starting surge matters more than running watts: this unit is rated 1500 W output (no separate peak published). That is below a typical 1/2 HP sump pump start (about 2150 W); check your pump label. Use the calculator with your exact pump.